£45,000 | | |
Status: | Available |
Tax Status: | Tax Exempt |
Location: |
Preston Marina Lancashire UK [View Map] |
A fast aluminium centre-cockpit cruising sailboat designed by Gary Mull.
IMCI certification completed.
Project boat, needing updating.
One previous owner.
Spacious aft cabin with Queen size bed. Aft head (needs rebuilding)
Comfortable forepeak cabin with head adjacent.
Midship saloon, galley and nav station.
Large engine room located below the cockpit with workbench/sea berth across the passageway.
Rugged construction, 1/4 inch aluminium plate below waterline. Frames on 3 foot centre with 1.5 inch T-stringers on 8 inch centres. Insulated above the waterline. Ballast 9500 lbs. Displacement approx 30,000 lbs. In mast furling mainsail, furling jib and large winches make single-handling possible.
Vessel type: | Cutter rigged sailboat |
Designer: | Gary Mull |
Builder: | Millerick Bros. Coast Marine USA |
Model: | Millerick Marine Custom Mull (one off) |
Fit Out: | Professional |
Constructed: | 1989 |
Berths: | 6 |
No. of engines: | 1 |
Engine model: | Yanmar 4JHSE |
Engine power: | 50 |
Engine hours: | 216 |
Fuel type: | Diesel |
Drive type: | Shaft drive |
Length over all: | 13.89m |
Beam: | 4.11m |
Maximum draft: | 2m |
Hull material: | Aluminium |
Hull type: | Round bilge |
Hull colour: | Grey unpainted |
Keel type: | Fin Keel |
Displacement: | 11 metric tons |
Dry Weight: | 11 metric tons |
Fuel capacity: | 200 Gallons |
Water capacity: | 78 Gallons |
Forward Cabin sleeps two in V berth. Hanging wardrobe and fitted cupboards and shelves.
Forward heads
Large saloon area with extending sea going berth
Navigation station
Galley (needs completion)
Corridor with sea going berth and entry to engine room under cockpit
Large aft cabin with queen size berth, hanging wardrobes and bookshelves
Aft heads which needs completion
Built by Millerick Marine, California, USA. Launched in 1989.
Aluminium round bilge hull, professionally fitted out.
1/4 inch aluminium plate construction below the waterline.
Frames on 3ft centre with 1.5inch T stringers on 8inch centres
Insulated above the waterline.
Three blade max prop
Barient winches, self tailing and manual
Lighthouse anchor windless
60lb CQR anchor re-galvanised
40lb Bruce anchor re-galvanised
200ft 3/8 BBB chain re-galvanised
Custom Kubota generator (needs maintenance), which drives 105 amp alternator, frig comp, WM pump, Watermaker
Trinada Watermaker
Solar panels
D400 Wind generator
Inverter 1800W (approx)
Battery charger
Force 10 stove (needs maintenance)
10 gallon hot water heater
10.5ft AB hard bottom dinghy
15 HP Yamaha Enduro outboard.
Watchmate AIS
CPT autopilot
Autohelm 6000
Autohelm 3000
Furuno GPS
Raytheon R-20 radar
Kenyon speed, depth and wind instruments with repeaters in the cockpit
West Marine VHF
ICOM HF Marine radio
DSP multi mode pactor controller
Yanmar 4JHSE 50 horsepower main engine, fitted in 2012 to comply with IMCI regulations.
216 hours on the clock.
Profurl roller furling
Main sail in mast furling.
Rigging replaced in 2008 with dyform rigging.
Main- original to the boat. Hood Stoway (500sq ft) good condition. (In storage at the marina)
Genoa- second hand, never used by us, bought to replace the old genoa, stowed in lazarette.
MPS Drifter (1350 sq ft) used a handful of times and in very good condition- stowed behind water tight bulkhead in the V berth.
Jib sail, good condition, also in storage.
Bimini cover - kept in storage
Spray hood will needs replacing/repair.
Mast keel stepped
Double spreader rig
Liferaft- not in date
MOB pole- currently in storage
Lidesling- currently in storage
Grab bag- in storage
Note: Indicated location is approximate general area only.